First AEG: I know you said to get a Marui...

[Flazzbog]

The stock can fit on the buffer tube I think. But you need to front wire the gun first. I don't know if the handguard fits on though.

Supposedly you can fit the pistolgrips on too if you dremel them a bit. There are magpul style mags available for them too. I think Reapernet knows a bit more about this topic though.

[ReaperNet]

Hey Flazz, does Magpul PTS furniture fit onto Marui Next Gen blowback M4's/HK416s?

Hi Seneschal, yes, aftermarket parts do fit Marui Next Gen weapons. If you're considering MOE furniture, check out the M4A1 SOCOM which comes front wired:

http://echigoya-guns.com/guns/index.php ... duct_id=51

[Eda]

Not stocks and grips, they different.

EDIT: For rear wired (416 and CQB-R's etc), as the battery comes through the stock,

[ReaperNet]

Not stocks and grips, they different.

Not sure why you think that, standard V2 stocks do fit, they're just really tight. Pistols grips fit too. Several examples out there. You don't have to google very hard to find them. As I suggested, get a front wired SOCOM M4A1.

Only Marui SCAR's do not accept aftermarket pistol grips because of the different lower receiver.

[Snorlax]

I like this. I'd leave the stock, since it's a pretty good VLTOR clone. I'd delete the Delta Ring, swap in a DD RIS-2 fore end, front and rear sights, grip, foregrip, and put a Noveske flash hider on it.

And then cry because I'm stuck with Marui and can't use P-Mags.

[ReaperNet]

And then cry because I'm stuck with Marui and can't use P-Mags.

But there are PTS P-Mags for Marui Next Gens. Also, you can buy a magwell adapter but you forfeit the bolt stop feature.

[Snorlax]

Oh, sweet.

[Eda]

Not stocks and grips, they different.

Not sure why you think that, standard V2 stocks do fit, they're just really tight. Pistols grips fit too. Several examples out there. You don't have to google very hard to find them. As I suggested, get a front wired SOCOM M4A1.

Only Marui SCAR's do not accept aftermarket pistol grips because of the different lower receiver.

Well that's good to know, I suppose I was just thinking my CQB-R because of wiring. But I actually didn't know that pistol grips were fine, what about 416's though because of that wee double cog for the ambi selector?

[ReaperNet]

what about 416's though because of that wee double cog for the ambi selector?

Good point, though it does just kinda sit there. So prolly only need a little grove to rest it on.

[Flazzbog]

I don't think the pistol grips have any special grooves or anything for the wee cog. So they're probably just as compatible as any others. Reaper or Jason can confirm.

[Snorlax]

Need confirmation that a Daniel Defense RIS-2 fits on a Marui CQB-R without a Delta Ring. Also, found an old pair of combat gloves in ranger green, I think, that I didn't know I had.

[PepsiCo]

If you mean the continuous rail system, some say the MAdbull DD lite rails do fit with shims, some say they fit with slight modification, some say they don't fit at all. I would imagine they fit with slight modification though. I'm looking to fix up my SOPMOD with a Madbull DD lite rail...but I've got other stuff to fix

[Snorlax]

I think I figured out that the Delta Ring is replaced by a Daniel Defense adaptor thing that screws on where the Delta Ring normally goes.

[Snorlax]

I bought some toys. Marui 5.1 Hi Capa, a whole bunch of bits and pieces for it (some of which may turn out to be shit and end up donated to the club/whoever wants them), Flyye 6094 vest, assorted TMC pouches that may also turn out crap.

Unrelated news:

https://www.youtube.com/watch?v=Lu_L1xmRcbU

[Snorlax]

PS. taking votes for new name. some of you have been complaining that none of yall niggas can pronounce seneschal